Many people want their car to always look like you were just driving it out from the car dealer, but they are clueless as to how. That why the question “How do I wash my car after ceramic coating” has become one of the mysteries among drivers.
Some people firmly believe that a ceramic coated car does not require maintenance because it has a long-lasting and durable shield to protect it. However, this is quite a misconception.
In order to keep a ceramic coated car looking as good as possible, you should regularly wash it using special car washing products.
In that article, we will give you a guide containing understandable and easy steps that show you how to clean your beloved car quickly. Let’s get started!
What Do You Need To Clean A Ceramic Coated Car?
There is no doubt that the quality of the equipment will be one of the most important criteria to successfully retain a swirl-free shine of your ceramic coated car. It may seem easy but paying attention to a few small details will make a big difference.
There are some basic tools you need to have in order to clean your car and those are:
- Wheel cleaning brushes
- Soap
- Buckets
- Microfiber cloths
- Towels for drying
- Ceramic coating maintenance spray
- Wash mitt
If you do not have them at home, you can get all of them easily on eCommerce sites such as Amazon or eBay.
How Do I Wash My Car After Ceramic Coating – 6 Simple Steps
Start with washing all the filthy stuff such as tree leaves or sand off your vehicle using a high-pressure washer. Then take the wheel brush, dip it in the soap and carefully scrub your wheels.
You do not need to be worried as this will not damage the ceramic coating on your car.
After that, it is time to go behind the rims. You can get the job done much faster if you have a smaller, thinner brush that can reach behind the spokes and all the holes of the wheels. If you want every corner of your wheels to be spotless, roll your car a little bit forward, so that the part of the wheel that stacked to the ground is now at the top.
Now is the time you can use your wash mitt.
You might want to start with washing your door, beginning from the top and moving downwards. If you do not have a wash mitt, you can use a small gentle brush instead.
If you have not looked into your engine bay for a longer time, I recommend you open it and gently wipe down on all surfaces. Following that, we now need a lot of water and will give our car a very refreshing shower.
A pressure washer would be the greatest choice for this task but if you cannot get your hands on one, regular garden hoses will suffice.
Make sure that you do not leave any part of the car unattended, especially the easy-to-miss spot such as underneath the rear bumper.
Place the two buckets near your car and fill one with clean water and another one with a mix of water and soap.
Then, dip your wash mitt into the soap water and wash your car thoroughly on all sides, one after another.
You do not want to heavily scrub your car as this could damage the coating, therefore it will be sufficient to go over each area two times.
It is also important to often clean your wash mitt in the clean water bucket and then dip it again into the soap bucket. From time to time, replace the water in your clean bucket.
You can use a smaller brush to clean some tight areas that are hard to access.
Now that you have finished washing your car, you need to rinse it one more time to remove all soap residues. When everything is completely washed off, we will move on with the next step drying your car.
Take a towel and fold it into half and wipe it down one side at a time. Wring the towel out and change the side whenever it gets soaked. Also, use a separate towel to dry the engine and the inner sides of the doors as well as the boot shuts.
You do not need to spend too much time on retaining your ceramic coating as it is a rather undemanding car shield compared to other types of coatings, like those using wax for example. A few minutes extra attention however will extremely increase the lifespan of your ceramic coating.
Consequently, take the microfiber towel and add a little bit of the coating maintenance spray and slightly polish your coating until it turns glossy.
Of course, it is not required but I strongly recommend you invest those few minutes and a good maintenance spray as you make the coating much more durable.
Now your car has already looked shiny on the outside, so I recommend that from time to time you clean both the inside of your car and the windows as well. You can use a vacuum cleaner for all the interior.
Next, use a soft sponge that is not likely to cause any scratches and wipe the windows using a little bit of water and glass cleaner.
Conclusion
Now you know the answer to “How to wash your car after ceramic coating?” As you saw, it is quite easy and not very time-consuming. Once again, if you clean your car regularly, it will always be quite fast as you do not build up too much dirt between the washing cycles. Anyway, simply follow the step-by-step guide above to and you can keep your newly coated vehicle in its best shape!